Knitting forks for beginners. scheme

Amazing scarves, stoles, dresses and blouses from large air loops, can be tied on a special device for needlework - a fork. This is an interesting technique, which is worth getting acquainted with.

Knitting lessons on the plug: familiarity with the technique

Knitting fork for beginners

Having first heard about knitting on a fork, many imagine kitchen utensils. In fact, a knitting fork is an ordinary piece of wire, only bent by the letter U.

There are universal knitting forks. With their help, you can change the length of the loops on the basis of the knitting method you choose, the thickness of the threads used and the result you want.

The universal knitting fork is 2 pieces of wire and 2 crossbars with small holes drilled in them. Depending on what exactly you want to tie, you have the opportunity to insert 2 wires closer or further to each other.

For knitting on a fork, you still need a hook. Choose his number on the basis of how thick the thread will work.

There are many ways to knit on the fork. Everything will depend on what kind of loops you will connect your thread: a crochet column, a single crochet column or a semi-column.

These are the most popular connecting loops.

Knitting on the fork: schemes

For more details, see

Knitting fork for beginners


  • Tie a loop on the hook.
  • Hold the hook in your right hand and the fork in your left. Get a working thread with a hook for your knitting fork.
  • Put the hook on the front part of the fork (approximately to the middle) and hook the working thread.
  • Make a loop.
  • Release the hook from the loop.
  • Twist it over the plug and re-insert it into the loop.
  • Turn the knitting fork clockwise so that your hook is in front again.
  • After completing this action, wrap the thread around the right side of your knitting fork.
  • In order for you to tie the next loop (and then all the others), you need to seize the working thread again and stretch it into the working loop.
  • Get a new loop on the hook. Then do steps 5 and 7.
  • Thus, you will be able to tie the strip length you need.
  • In order to finish knitting, cut the working thread, leaving 4 cm. Grab the working thread with a hook and pull it through the loop.
  • Pull the thread by the tip, tightening the loop in this way.
  • Now you can pull off the air strips from your fork and use for the subsequent knitting of things.
  • These strips of semi-columns knit very quickly, the loops are tied together by weak knots and can easily dissolve. Only very experienced needlewomen can work with light air strips.
  • If you pull the 2 ends of the strips in different directions, you get a decorative lace that can be used when processing knitted products.

Knitting fork for beginners

Column without nakida

  • A single crochet helps to weave air loops between each other much better.
  • The beginning of such knitting is not at all different from the method described above.
  • Repeat all steps 1-7.
  • Next, enter the hook into the air loop.
  • Grab the thread (cap) and pull the loop.
  • Once again, grab the working thread (nakid) and pull it through 2 loops on the hook.
  • You should have a new loop on the hook. Repeat steps 5-7 and again make a single crochet.
  • So knit the strip to the desired length.
  • It is much easier to work with the air strip. The knitting speed is higher than average.

Knitting on the fork: models

On the plug you can link a lot of original models. One of them is a palatine.

Tippet: knitting on a fork

How to tie a fork on a fork? For the manufacture of products with a size of 35 cm-15 cm, you will need:

fine yarn (mohair 40 percent, acrylic 60 percent, 500 m) - 100 g, fork (8 cm wide), hook with No. 3.

  1. Make 4 tapes on the fork. On each side of the strip you should have 378 long loops. The tapes are long, so you can tie them from 2 parts, which then connect. Wavy fan pattern will collect the length of your strips, shortening them almost 2 times.
  2. Tie and connect the stripes in this way.
  3. Pattern repeat: Art./n of 3 long loops, 8 air loops, repeat 7 more times, Art. b / n from the 21st long loop, 8 air loops.
  4. Repeat rapport 9 times on one side of the strip, and on the other strip, start with tying st. b / n from the 21st long loop, 8 rev. loops, then 7 times st. b / n from 3 long loops, 8 vozd. loops.
  5. Tying the 1st lane, attach the 2nd one to the 1st lane during the tying process. The joints of the central arches of the air loops are made by completing 4 air loops, knit art. b / n from the arch of another tape, 4 air loops, art. b / n from a group of loops, the repeat of your pattern should be arranged linearly.
  6. Tying and connecting all your stripes neatly, you will get a beautiful openwork tippet.

Knitting fork: video

Knitting on a fork is an exciting technique that allows you to create a variety of elegant and original things. Learning such needlework is quite simple, especially if you have good crochet skills.

Add a comment